[ Pobierz całość w formacie PDF ]
.1 What information about the router and its startup process can be gathered from the output of the show version command1 What information about the router and its startup process can be gathered from the output of the show version command? (Choose three.)the last restart method *the tftp software version installed the amount of NVRAM and FLASH used the configuration register settings *the location used for loading the IOS *2 What baud rate needs to be configured on terminal emulation software to allow a connection to the console port of a router?2400 4800 9600 *14200 384003 Which of the following is the correct flow of routines for a router startup?load bootstrap, load IOS, apply configuration *load bootstrap, apply configuration, load IOS load IOS, load bootstrap, apply configuration, check hardware check hardware, apply configuration, load bootstrap, load IOS4 Which of the following statements concerning router interface modes are correct? (Choose three.)User EXEC mode provides commands to monitor router operation.*Privileged EXEC mode only provides commands to change or configure router operation.Password protected configuration modes can be accessed from either user EXEC or privileged EXEC modes.On a router with the name Core1, the prompt indicating privileged EXEC mode is Core1#.*The command to enter privileged EXEC mode is Router# enable.A username and password may be required to enter privileged EXEC mode.*5 Which keystroke is used to move to the beginning of a command line?Ctrl-A *Ctrl-B Esc-A Esc-B Ctrl-C Ctrl-Z6 What is the maximum number of commands allowed in the history buffer?10 20 128 255 256 *7 Which tasks can be performed in the ROM monitor mode? (Choose two.)recover from system failures *create startup configuration files recover from lost passwords *configure IP addresses on all router interfaces perform high level diagnostics8 What is the default sequence for loading the IOS?NVRAM, TFTP, FLASH NVRAM, TFTP, CONSOLE FLASH, ROM, TFTP FLASH, TFTP, ROM *TFTP, FLASH, ROM9Which of the following identifies the correct items needed to initially configure a router?1) DB-9-to-RJ-45 on the PC's serial port 2) a straight through cable 3) the router's console port 1) PC's Ethernet port 2) a crossover cable 3) the router's Ethernet port 1) DB-9-to-RJ-45 on the PC's serial port 2) a rollover cable 3) the router's Ethernet port 1) PC's Ethernet port 2) a rollover cable 3) the router's console port 1) DB-9-to-RJ-45 on the PC's serial port *2) a rollover cable 3) the router's console port 1) PC's Ethernet port 2) a rollover cable 3) the router's Ethernet port10 When the router output is being viewed through a terminal program, which statements are true regarding the --More-- prompt at the bottom of the router display? (Choose two.)Press the Spacebar to display the next line.Press the Spacebar to view the next screen.*Press the PgDn key to view the next screen.Press the Enter key to display the next line.*Press the Enter key to view the next screen.11 Which connection method can be used to perform the initial configuration of a router?use a serial connection of a computer connected to the console port of a router *telnet to the router through a serial port use a vty port through the Ethernet interface use a modem connected to the AUX port of the router12 What information does the name of the IOS file provide to the network administrator? (Choose three.)the amount of NVRAM required to run the image the hardware platform the image runs on *the various software platforms the image can run on special features and capabilities of the image *the bandwidth supported by the IOS where the image executes from and if it has been compressed *13 Under what conditions does the router enter setup mode? (Choose three.)immediately after issuing the command Router#erase start after issuing the command Router#setup *during the initial configuration of a router *after deleting the backup configuration and reloading the router *after deleting the running configuration14 What does the command sh? return as output if issued at the Router# prompt?all show commands allowed in privileged mode all commands beginning with the letters sh *an incomplete command error message an invalid command error message15 Cisco IOS software is separated into two levels as a security feature.What are those two levels? (Choose two.)global privileged *local user *interface 16 Which keystrokes can be used to return to the privileged mode from the interface configuration mode?Ctrl-P Ctrl-Shift-6, then X Ctrl-Z *Esc17 Which command takes precedence if the commands enable password and enable secret are both configured on a router?enable password enable secret *Neither.They are both enabled.Neither.They cancel each other out.18 The active IOS of the router is initialized from FLASH.In this scenario, what commands would be used to display the name of the active IOS? (Choose two.)Router#show IOS Router#show flash *Router#show nvram Router#show version *Router#show startup-config Router#show running-config19 A network administrator needs to configure a router.Which of the following connection methods requires network functionality to be accessible?console AUX Telnet *modem20 What is the default sequence for loading the configuration file?NVRAM, FLASH, ROM FLASH, TFTP,CONSOLE NVRAM, TFTP, CONSOLE *FLASH, TFTP, ROM21 Which tasks can be accomplished by using the command history feature? (Choose two.)View a list of commands entered in a previous session.Recall up to 15 command lines by default.Set the command history buffer size.*Recall previously entered commands.*Save command lines in a log file for future reference
[ Pobierz całość w formacie PDF ]