[ Pobierz całość w formacie PDF ]
.SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV.00www.cobra.itXMAKESUBARUMOD.FORESTERYEAR98 → PETROLDIESELALARM/SIRENPosition the compact alarm and the sirens in the engine compartmernt, on the POSITIONbulkhead, drivers side, that divides the engine compartment and the passengers compartment.CENTRAL UNIT POSITIONPosition the modular systems and the modules under the dashboard, drivers side.Pass the cables through the original rubber sleeve located in the left lateral bulkhead, drivers side.POWER SUPPLY+30: Connect to the 4 mm2 WHITE wire located in the 4 way blue connector under the steering column.- 31: Connect with a ring terminal to the car body.IGNITION WIREConnect to the 4 mm2 GREEN wire located in the wiring harness coming out of the 4 way blue connector under the steering column.DIRECTION INDICATORSConnect to the 0,75 mm2 BLACK/GREEN and LIGHT GREEN/BLACK wires located in the wiring harness coming out of the 20 way white connector under the steering column.ELECTRIC WINDOWSPositive control signalFront window, drivers side Cut the 1,5 mm2 BLUE/RED wire.Front window, passengers side Cut the 1,5 mm2 BLUE/RED wire.Rear window, drivers side Cut the 1,5 mm2 BLUE/RED wire.Rear window, passengers side Cut the 1,5 mm2 BLUE/RED wire.These connections should be effected in the wiring harness coming out of the 9way transparent connector behind the sill cover, drivers side.For the drivers side window the connection should be effected on the coming out of the inner switch of the drivers side door.CENTRAL DOORS LOCKINGConnect to the 0,75 mm2 WHITE wire located in the wiring harness coming out of the 12 way white/black connector located in the coming out of the central door locking unit above the fuse box.Refer to diagram nr.57 for the Bridge serie antitheft or to diagram nr.57A for 3100 serie antitheft.IMMOBILISATION POINT 1Fuel pumpCut the 0,75 mm2 GREEN/ORANGE wire located in the wiring harness coming out of the 4 way green connector joined to the relay of the fuel pump.This relay is fastened on the bracket behind the fuse box.BONNET SWITCHInstall an additional switch on the headlamp support plate, near the original bonnet bumper rubber.DOORS AND BOOT SWITCHConnect to the 0,5 mm2 YELLOW wire located in the wiring harness that comes out of the 12 way white/black connector and coming out of the central door locking unit above the fuse box.Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed sufor98gbb.docas per the instructions given on the product installation manual.SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV.00www.cobra.itFITTING DIAGRAM N°57Diagram for doors locking on SUBARU FORESTER(for Bridge serie antithefts) VIOLET/ORANGE VIOLET ORANGE YELLOW/BLACKCentral doors lockingunitMDriver’s side door0,5mm2 WHITE wire, in the 12 way white/black connector, coming switchout of the central doors locking unit located above the fuse box.With this diagram, the locking is made with the breaking of the wire, the opening with a ground signal.Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed sufor98gbb.docas per the instructions given on the product installation manual.SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV.00www.cobra.itFITTING DIAGRAM N°57ADiagram for doors locking on SUBARU FORESTER(for 3100 serie antithefts)VIOLET/WHITE VIOLET ORANGE YELLOW/BLACKORANGE/WHITECentral doors lockingunitMDriver’s side door0,5mm2 WHITE wire, in the 12 way white/black connector, coming switchout of the central doors locking unit located above the fuse box.With this diagram, the locking is made with the breaking of the wire, the opening with a ground signal.Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed sufor98gbb.docas per the instructions given on the product installation manual
[ Pobierz całość w formacie PDF ]